• / 161
  • 下载费用:10 金币  

思科Nexus_7000产品手册.ppt

关 键 词:
思科Nexus_7000产品手册.ppt
资源描述:
Nexus 7000 NX-OS:用于数据中心的操作系统,目录,基本概述 初步启动系统验证 命令行界面(CLI)概述 接口配置2层交换和生成树配置路由协议配置FHRP配置 验证IP转发 安全协议配置 系统管理协议配置 疑难解答工具,Nexus 产品线概述,数据中心方面,Nexus 5000,Nexus 2000,Nexus 1000v,NX-OS,,Nexus 7000,高可用性高性能(10GE)40/100 GE Ready统一的IO/DCB (Future),,高性能小体形统一的 IO/DCB (FCoE)虚拟交换机(FEX),,IBM 刀片交换机10 GE连通性统一的IO/DCB (FCoE),,远程连接卡(FEX)连接到Nexus 50001GE to 10GE过渡简化的Mgmt,,虚拟交换机VMWare综合应用NX-OS奇偶特征简化Mgmt,Nexus 4000,Typical Nexus 7000 部署,L3 核心,L2 汇聚,序列中,万兆以太网,,Nexus 7000 端到端,,,基本概述,Nexus 7010 (10-槽) 概述Nexus 7018 (18-槽) 概述管理引擎以太网模块交换矩阵电源,Nexus 7010 - 10 槽 概述,Nexus系列之一 针对数据中心做优化 高密度 多达256个万兆接口,384 1G的接口 高性能 高达1.4 Tbps的系统总带宽 高达80 Gbps的每插槽带宽 每插槽高达60 Mpps的吞吐量 高达480 Mpps的系统总吞吐量 未来可实现 高达4.1 Tbps的系统带宽(每槽230G)的初始功能模块 可扩展到8 + Tbps的系统带宽(500 + G每槽) 由前至后气流 所有组件冗余并支持热插拔 用于综合布线的专用组建 21 U,Nexus 7010 –正面和背面视图,,线卡插槽(8),风扇过滤器(可选),,模块顶掣,,,系统状态LEDs,,,,线缆盖,,,,,交换矩阵(最多5),,电源(最多3),,矩阵风扇,,,模块顶掣,,,系统风扇,Nexus 7018 - 18 槽 概述,Nexus系列二 针对数据中心环境做优化 最高密度 多达512个万兆接口,768 1G的接口 高性能 高达2.8 Tbps的系统总带宽 高达80 Gbps的每插槽带宽 每插槽高达60 Mpps的吞吐量 高达960 Mpps的系统总吞吐量 未来可支持的 高达8.2 Tbps的系统带宽(每槽230克)的功能模块 可扩展到16 + Tbps的系统带宽 侧侧气流 所有组件冗余并支持热插拔 25U,,Nexus 7018 –正面和背面视图,线卡插槽 (1-8),线卡插槽 (11-18),管理引擎 (9-10),,系统状态LEDs,交换矩阵(最多5),,,,电源(最多4个),,,系统风扇托盘,,,电源进气,,,,,,线卡散热孔,,,,电源排气,设备尺寸和重量,,,,,,,17.3 in,Nexus 7018,Nexus 7010,17.3 in,21 RU,25 RU,36.5 in,33.1 in,43.5 in,33.1 in,模块顶杠杆,管理引擎交换矩阵以太网,模块包含驱动杠杆,不仅帮助协调和安装模块,而且具有开关模块的功能。如果两个模块同时按下,自动关闭模块的供电。,支持杠杆的模块:,验证:,n7000# show module 1 Mod Ports Module-Type Model Status --- ----- -------------------------------- ------------------ ------------ 1 32 10 Gbps Ethernet Module N7K-M132XP-12 okChassis Ejector Support: Enabled Ejector Status: Top ejector CLOSE, Bottom ejector CLOSE, Module HW does support ejector based shutdown.,,管理模块,双核心Intel Xeon处理器4 GB的内存2 GB的闪存(8 GB的日志和2 GB的扩展)2 MB NVRAM1 10/100/1000自适应以太网口1控制端口和辅助端口1 CMP 10/100/1000 以太网口3 USB 口 (2 host – 1 device),管理引擎 I,前面板,控制口,辅助口,以太口,CMP 口,,,,,,USB device口,,USB host口,,Reset 按钮,,,,状态灯,,Log & Exp. Flash,,管理引擎连接方式,Sup 1,Sup 2,,,,,,,,,,IP Address A (Shared IP),IP Address B,IP Address C,IP Network,IP Network,Console,IP Mgmt,CMP,RS-232 Terminal Server,“Active” 状态内带外以太网端口,内带外管理选项,Note: The chassis can be managed in-band using IPv4 or IPv6 (Loopback’s, SVI’s, Physical Interfaces),“mgmt 0”端口 在自己的VRF中 (管理),以太网模块,32个万兆以太网端口(SFP+ Optics)80个千兆光纤连接60 Mpps的IPv4转发128K MAC, 128K FIB, 512K NetFlowQoS Queues (RX:8q2t) (TX:1p7q4t)巨型帧(9216),48个10/100/1000 M端口(双绞线)40个千兆光纤连接60 Mpps的IPv4转发128K MAC, 128K FIB, 512K NetFlowQoS Queues (RX:2q4t) (TX:1p3q4t)巨型帧(9216),48端口10/100/1000(双绞线)模块,32端口万兆以太网模块,48 个G口(光口)40个千兆光纤连接60 Mpps的IPv4转发128K MAC, 128K FIB, 512K NetFlowQoS Queues (RX:2q4t) (TX:1p3q4t)巨型帧(9216),48口千兆光模块,交换矩阵,每机箱最多5个模块5模块提供230Gbps的I/O插槽46Gbps的I/O插槽每模块全矩阵模块均分负载热插拔 (非破坏性的),交换矩阵I,每个功能模块都带来带宽的增加1G模块需要2块交换矩阵做N+1冗余10G模块需要3块交换矩阵做N+1冗余第四五块 provide additional level of redundancy 未来将利用额外的模块结构带宽Fabric failure results in reduction of overall system bandwidth,交换矩阵能力和冗余,Nexus 7010 Fabric module,用于光纤连接的2个I / O模块,46 Gbps,138 Gbps,184 Gbps,230 Gbps,92 Gbps,,,,,,,,,,,230,230,46,46,46,46,46,46,46,46,46,46,48 Port 1GE SFP,32 Port 10GE SFP+,Requires 43Gbps,Requires 80Gbps,Fabric 1,Fabric 2,Fabric 3,Fabric 4,Fabric 5,,电源,通用的普通电源!,双20安培电路(110伏及220伏)IEC C19 电缆 (16A)10 电缆可用(见数据表),双30安培电路(110伏及220伏) 综合12'电缆(24A)IEC 60309 or NEDA L6-30 Plug,7010所需的最大功率 = ~9Kw - 7018 = ~15Kw,6Kw (AC),7.5Kw (AC),电源输入/输出功率,7,500瓦电源,6000瓦电源,每个组件需要的功率,7010 需要2400w 启动 7018 需要2193w 启动,电源需求:,下表列出了一般情况下的最大功率和每个组件需要的功率。在一般的情况下,组件用不到最大功率。,,,,,,,,,电源冗余模式综述,全冗余,N+1 冗余,GRID 冗余,组合型,,,,,没有冗余!,Can Lose 1 PS,Can Lose 1 PS or 1 GRID,Can Lose 1 GRID,X,X,X,X,可用功率= ~9Kw,可用功率= ~12Kw,备用功率= ~6Kw,可用功率= ~18Kw,备用功率= 0Kw,可用功率= ~9Kw,备用功率= ~9Kw,备用功率= ~9Kw,(6x 220v = 18Kw),(6x 220v = 18Kw),用于Nexus 7010的6Kw电源,默认状态,(6x 220v = 18Kw),(6x 220v = 18Kw),通用的 7010/7018 基本零件,,,,管理引擎I/O模块(以太网)电源(两种模式),,,系统验证 配置,NX-OS版本综述I/O模块、功能模块和风扇状态可编程逻辑器件和BIOS版本功率预算和环境温度监测管理冗余和替换,验证软件版本,n7000# show version Cisco Nexus Operating System (NX-OS) Software TAC support: http://www.cisco.com/tac Copyright (c) 2002-2008, Cisco Systems, Inc. All rights reserved. The copyrights to certain works contained in this software are owned by other third parties and used and distributed under license. Certain components of this software are licensed under the GNU General Public License (GPL) version 2.0 or the GNU Lesser General Public License (LGPL) Version 2.1. A copy of each such license is available at http://www.opensource.org/licenses/gpl-2.0.php and http://www.opensource.org/licenses/lgpl-2.1.phpSoftwareBIOS: version 3.15.0loader: version N/Akickstart: version 4.0(1)system: version 4.0(1)BIOS compile time: 03/04/08kickstart image file is: bootflash:/n7000-s1-kickstart.4.0.1.binkickstart compile time: 3/6/2008 2:00:00 [04/02/2008 08:12:57]system image file is: bootflash:/n7000-s1-dk9.4.0.1.binsystem compile time: 3/6/2008 2:00:00 [04/02/2008 08:58:14]Hardwarecisco Nexus7000 C7010 (10 Slot) Chassis (“Supervisor module-1X“)Intel(R) Xeon(R) CPU with 4129620 kB of memory.Processor Board ID JAB114000CCDevice name: n7000bootflash: 2030616 kBslot0: 0 kB (expansion flash)Kernel uptime is 0 day(s), 15 hour(s), 9 minute(s), 39 second(s),文件位置,系统版本,,,,,Bootflash (Size) 扩展flash – 不存在,,,,系统内存(KB),,NX-OS software,使用show version命令以获取软件/硬件的信息。,系统正常运行时间,,验证模块状态,n7000# show module Mod Ports Module-Type Model Status --- ----- -------------------------------- ------------------ ------------ 1 48 10/100/1000 Mbps Ethernet Module N7K-M148GT-11 ok 2 48 10/100/1000 Mbps Ethernet Module N7K-M148GT-11 ok 3 32 10 Gbps Ethernet Module N7K-M132XP-12 ok 4 32 10 Gbps Ethernet Module N7K-M132XP-12 ok 5 0 Supervisor module-1X N7K-SUP1 active * 6 0 Supervisor module-1X N7K-SUP1 ha-standbyMod Sw Hw World-Wide-Name(s) (WWN) --- -------------- ------ -------------------------------------------------- 1 4.0(1) 0.902 -- 2 4.0(1) 0.902 -- 3 4.0(1) 0.504 -- 4 4.0(1) 0.504 -- 5 4.0(1) 0.801 -- 6 4.0(1) 0.801 -- Mod MAC-Address(es) Serial-Num --- -------------------------------------- ---------- 1 00-1b-54-c1-00-38 to 00-1b-54-c1-00-6c JAB114100WE 2 00-1b-54-c0-fe-cc to 00-1b-54-c0-ff-00 JAB114100WK 3 00-1b-54-c1-0b-cc to 00-1b-54-c1-0b-f0 JAB114602F7 4 00-1b-54-c1-0a-64 to 00-1b-54-c1-0a-88 JAB114602FD 5 00-1b-54-c0-fe-b8 to 00-1b-54-c0-fe-c0 JAB114000CC 6 00-1b-54-c0-ff-18 to 00-1b-54-c0-ff-20 JAB114000R1* this terminal session,,模块状态 其他状态: powered-dn powered-up pwr-cycld pwr-denied testing initializing,,,模块类型和模式#,,模块 #,,#每个模块的端口,使用show module的命令,以确定每个模块状态.,在Sup-1上的当前用户终端会话,,,n7000# reload module 1 n7000(config)# poweroff module 1,“重启” 或 “关闭” 模块,,,Powering down Modules:,验证模块“正常运行时间”,n7000# show module uptime ------ Module 1 ----- Module Start Time: Fri Dec 12 07:05:33 2008 Up Time: 6 days, 17 hours, 31 minutes, 8 seconds------ Module 2 ----- Module Start Time: Sun Nov 9 00:58:28 2008 Up Time: 39 days, 23 hours, 38 minutes, 13 seconds------ Module 3 ----- Module Start Time: Fri Dec 12 06:21:38 2008 Up Time: 6 days, 18 hours, 15 minutes, 3 seconds------ Module 5 ----- Module Start Time: Tue Nov 11 01:04:46 2008 Up Time: 37 days, 23 hours, 31 minutes, 55 seconds------ Module 6 ----- Module Start Time: Tue Nov 11 01:34:10 2008 Up Time: 37 days, 23 hours, 2 minutes, 31 seconds------ Xbar 1 ----- Xbar Start Time: Sun Nov 9 00:55:57 2008 Up Time: 39 days, 23 hours, 40 minutes, 44 seconds------ Xbar 2 ----- Xbar Start Time: Sun Nov 9 00:56:00 2008 Up Time: 39 days, 23 hours, 40 minutes, 41 seconds------ Xbar 3 ----- Xbar Start Time: Sun Nov 9 00:56:02 2008 Up Time: 39 days, 23 hours, 40 minutes, 39 seconds,使用show module uptime命令,以确定每个模块已开始运作多久。,,32端口万兆以太网模块,,管理引擎,,交换矩阵,验证功能模块状态,n7000# show module fabricXbar Ports Module-Type Model Status --- ----- -------------------------------- ------------------ ------------ 1 0 Xbar N7K-C7010-FAB-1 ok 2 0 Xbar N7K-C7010-FAB-1 ok 3 0 Xbar N7K-C7010-FAB-1 okXbar Sw Hw World-Wide-Name(s) (WWN) --- -------------- ------ -------------------------------------------------- 1 NA 0.404 -- 2 NA 0.404 -- 3 NA 0.404 -- Xbar MAC-Address(es) Serial-Num --- -------------------------------------- ---------- 1 NA JAB114700X6 2 NA JAB114700WQ 3 NA JAB114700WZ,,模块状态,,插槽 #,使用show module fabric命令以确定每个功能模块的状态,Note: Only 3 out of 5 功能模块 are present,验证模块的使用情况,Use the show hardware fabric-utilization命令来查看当前模块的使用情况。,n7000# show hardware fabric-utilization ----------------------------- Slot Direction Utilization -----------------------------1 ingress 0%1 egress 0%2 ingress 0%2 egress 0%5 ingress 0%5 egress 0% -----------------------------,,每个模块入口/出口 利用的百分比,n7000# show hardware fabric-utilization detail module 1 ---------------------------------------------------------------------- Fabric Planes: A -- Unicast fabric interface B -- Multicast/Multidestination fabric interface ---------------------------------------------------------------------- I/O Fabric Fabric Fabric Fabric Slot Mod Instance Channel ID Plane Direction Utilization ---------------------------------------------------------------------- 1 1 1 5 A ingress 0% 1 1 1 5 A egress 0% 1 1 1 5 B ingress 0% 1 1 1 5 B egress 0% 1 1 1 3 A ingress 0% 1 1 1 3 A egress 0% 1 1 1 3 B ingress 0% 1 1 1 3 B egress 0% ,非常详细的分类,验证机箱风扇,n7000# show environment fan Fan: ------------------------------------------------------ Fan Model Hw Status ------------------------------------------------------ Fan1(sys_fan1) N7K-C7010-FAN-S 0.409 Ok Fan2(sys_fan2) N7K-C7010-FAN-S 0.409 Ok Fan3(fab_fan1) N7K-C7010-FAN-F 0.209 Ok Fan4(fab_fan2) N7K-C7010-FAN-F 0.209 Ok Fan_in_PS1 -- -- Ok Fan_in_PS2 -- -- Ok Fan_in_PS3 -- -- Absent Fan Air Filter : Absent,使用show environment fan命令来验证机箱风扇和电源风扇的状态。,,风扇状态,,可选的空气过滤器未安装,,电源风扇状态,Note: 4/4个电源板被安装,2/3个电源被安装。 可选的空气过滤器没有安装。,验证功率的预算及使用,n7000# show environment power Power Supply: Voltage: 50 Volts Power Actual Total Supply Model Output Capacity Status(Watts ) (Watts ) ------- ------------------- ----------- ----------- -------------- 1 N7K-AC-6.0KW 0 W 0 W Shutdown 2 N7K-AC-6.0KW 712 W 3000 W Ok 3 N7K-AC-6.0KW 1539 W 6000 W Ok Actual Power Module Model Draw Allocated Status(Watts ) (Watts ) ------- ------------------- ----------- ----------- -------------- 1 N7K-M132XP-12 N/A 750 W Powered-Up 2 N7K-M132XP-12 N/A 750 W Powered-Up 3 N7K-M148GT-11 N/A 400 W Powered-Up 4 N7K-M148GT-11 N/A 400 W Powered-Up 5 N7K-SUP1 N/A 210 W Powered-Up 6 N7K-SUP1 N/A 210 W Powered-Up Xb1 N7K-C7010-FAB-1 N/A 60 W Powered-Up Xb2 N7K-C7010-FAB-1 N/A 60 W Powered-Up Xb3 N7K-C7010-FAB-1 N/A 60 W Powered-Up Xb4 xbar N/A 60 W Absent Xb5 xbar N/A 60 W Absent fan1 N7K-C7010-FAN-S N/A 720 W Powered-Up fan2 N7K-C7010-FAN-S N/A 720 W Powered-Up fan3 N7K-C7010-FAN-F N/A 120 W Powered-Up fan4 N7K-C7010-FAN-F N/A 120 W Powered-UpN/A - Per module power not availablePower Usage Summary: -------------------- Power Supply redundancy mode (configured) PS-Redundant Power Supply redundancy mode (operational) Non-Redundant Total Power Capacity (based on configured mode) 9000 W Total Power of all Inputs (cumulative) 9000 W Total Power Output (actual draw) 2251 W Total Power Allocated (budget) 4700 W Total Power Available for additional modules 4300 W,,电力供应#,,每个组件的电源需求 * I/O模块 * 功能模块 *风扇,,电源冗余状态,,每个电源总发电量和实际用电量,,总容量及使用情况,,,,未来功能,验证机箱温度,n7000# show environmental temperatureTemperature: -------------------------------------------------------------------- Module Sensor MajorThresh MinorThres CurTemp Status(Celsius) (Celsius) (Celsius) -------------------------------------------------------------------- 1 Crossbar(s5) 105 95 35 Ok 1 CTSdev1 (s6) 115 105 67 Ok 1 CTSdev2 (s7) 115 105 59 Ok 1 CTSdev3 (s8) 115 105 54 Ok 1 CTSdev4 (s9) 115 105 50 Ok 1 CTSdev5 (s10) 115 105 47 Ok 1 CTSdev6 (s11) 115 105 51 Ok 1 CTSdev7 (s12) 115 105 46 Ok 1 CTSdev8 (s13) 115 105 48 Ok 1 CTSdev9 (s14) 115 105 43 Ok 1 CTSdev10(s15) 115 105 42 Ok 1 CTSdev11(s16) 115 105 39 Ok 1 CTSdev12(s17) 115 105 40 Ok 1 QEng1Sn1(s18) 115 110 44 Ok 1 QEng1Sn2(s19) 115 110 42 Ok 1 QEng1Sn3(s20) 115 110 40 Ok 1 QEng1Sn4(s21) 115 110 42 Ok ,,状态,Note: CLI omitted due to the number of temperature sensors per component.,,模块 #,使用show env temp命令来验证每个模块温度值。 如果minor或者major的数值相同,那么SNMP将会发送报警消息。,组件,,,验证和管理设备冗余情况,n7000# show system redundancy statusRedundancy mode ---------------administrative: HAoperational: HAThis supervisor (sup-1) -----------------------Redundancy state: ActiveSupervisor state: ActiveInternal state: Active with HA standby Other supervisor (sup-2) ------------------------Redundancy state: StandbySupervisor state: HA standbyInternal state: HA standby,n7000# show system uptimeSystem start time: Tue May 24 03:37:31 2005 System uptime: 0 days, 15 hours, 26 minutes, 10 seconds Kernel uptime: 0 days, 15 hours, 28 minutes, 5 seconds Active supervisor uptime: 0 days, 15 hours, 26 minutes, 10 seconds,用show system redundancy status 命令来查看“Active/Standby” 和高可用性(HA) 管理状态.,,系统正常运行时间,,,,Sup-1 = Slot 5 “Active” Sup-2 = Slot 6 “Standby”,,“Active” 状态时间,Supervisor Switchover,n7000# show system redundancy status Redundancy mode ---------------administrative: HAoperational: HAThis supervisor (sup-1) -----------------------Redundancy state: ActiveSupervisor state: ActiveInternal state: Active with HA standby Other supervisor (sup-2) ------------------------Redundancy state: StandbySupervisor state: HA standbyInternal state: HA standby,n7000# system switchover,n7000# show system redundancy status Redundancy mode ---------------administrative: HAoperational: HAThis supervisor (sup-2) -----------------------Redundancy state: ActiveSupervisor state: ActiveInternal state: Active with HA standby Other supervisor (sup-1) ------------------------Redundancy state: StandbySupervisor state: HA standby Internal state: HA standby,
展开阅读全文
  微传网所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。
0条评论

还可以输入200字符

暂无评论,赶快抢占沙发吧。

关于本文
本文标题:思科Nexus_7000产品手册.ppt
链接地址:https://www.weizhuannet.com/p-9809824.html
微传网是一个办公文档、学习资料下载的在线文档分享平台!

网站资源均来自网络,如有侵权,请联系客服删除!

 网站客服QQ:80879498  会员QQ群:727456886

copyright@ 2018-2028 微传网络工作室版权所有

     经营许可证编号:冀ICP备18006529号-1 ,公安局备案号:13028102000124

收起
展开