• / 2
  • 下载费用:10 金币  

科勒花洒~72722t_72723t.pdf

关 键 词:
科勒花洒~72722t_72723t.pdf
资源描述:
所有的资料是按最新出版的产品资料编写而成。科勒公司保留任何时候不经通知即可改变产品特性、包装或产品可供类型的权利。说明书包括重要的安装、保养及清洁方面的内容,请把这些资料交给用户阅读。注意事项 :1.一定要先彻底冲洗供水管以清除管道中的杂质。 2.切换器正常工作的最小压力为0.05MPa(0.5bar)。3.花洒最高工作压力:0.5MPa(5bar)。水压超过0.5MPa(5bar)须安装减压阀。花洒最高工作温度及环境温度:60°C。请特别注意花洒同花洒连接的臂管须远离浴霸,否则可能损坏花洒及其密封件,甚至对使用者造成伤害。BEFORE YOU BEGINAll information is based on the latest product information available at the time of publication. Kohler Co. reserves the right to make changes in product characteristics, packaging, or availability at any time without notice. Please leave these instructions for the consumer. They contain important information.NOTES:1. Flush the water supply pipes thoroughly to remove debris.2. The minimum inlet water pressure for the diverter is 0.05MPa(0.5bar).3. The highest working pressure for handspray is 0.5MPa(5bar). If it exceeds 0.5MPa(5 bar), a pressure reducer is needed. The highest water and environment temperature is 60°C. Please keep handspray, showerhead and the shower arm away from heater, or it may become damaged and cause injury to the user.1060461-2-A 1 12051T 12052T 72722T 72723T 挂墙式浴缸花洒龙头12051T 12052T 72722T 72723T 挂墙式浴缸花洒龙头安装之前安装尺寸 ROUGH-IN DIMENSIONS**订购时请说明颜色编号**Color code must be specified when orderingINSTALLATION INSTRUCTIONS 安装说明书 Wall-Mount Bath/Shower FaucetSERVICE PARTS 零 件 图1060461-2-A 4 150±1625177G1/2“G1/2“G1/2“G1/2“Ø54130Ø6382.5880084O-RingO型圈880085O-RingO型圈870992O-RingO型圈835701**Shower Bracket托架834791**Bonnet阀帽834792Nut螺母834460Valve 阀芯1139553**Connectors连接套件835014**Connector连接件835700**Handspray花洒(仅用于12051T/12052T )880091Water Flow Restricter限流器(仅用于12051T/12052T)831727**Hose软管1142980**Lever Handle 把手834801**Auto Diverter 自动分水器(仅用于72722T )835010**Manual Diverter 手动分水器(仅用于72723T )Wall-Mount Bath/Shower Faucet将手柄轻轻提起,向左转为热水,右转为冷水。 Lift the handle gently. Turn left for hot water, right for cold water.使用说明 HANDLE OPERATION87Ø902261500G1/2“1181007**Handspray花洒(仅用于72722T /72723T)1030624Water Flow Restricter限流器834562**Aerator起泡器880002Plug Button Kit塞扣套件1060461-2-A 2 安装 说明 INSTALLATIONHow To Install The FaucetInstall the two offset connectors(1) into the hot and cold supply pipes. Use thread tape on pipe threads.Adjust the center-to-center distance between the connectors to 150mm and level.如何安装水龙头在两个接头(1)涂上螺纹密封膏或缠绕密封胶带,然后旋入冷热供水管中。调节两个接头,使其中心距离为150mm并保持同一水平。Thread the trim caps(2) onto the connectors until they contact the finished wall.将装饰罩(2)旋入接头,紧贴装修后的墙壁。Insert washer seals(4) into supply nuts(5) of the faucets.Thread the faucet supply nuts onto the connectors and tighten.Connect shower hose(6) to faucet shower outlet(7) and handspray(8). Seals(9) provided with hose must be installed in each end.把密封垫片(4)装进螺母(5) 后,旋接到接头,并拧紧。将垫圈(9)装入淋浴软管(6) 的两头,再把淋浴软管的一端接到水龙头的出口(7),另一端接花洒(8)。12457986150mm热HOT815冷COLD1060461-2-A 3 1010How To Install The BracketTake off the locking pin(11) from the bracket(10). Take out the self-tapping screws(12) and anchors(14) from the inside of the bracket by pulling out the plastic sleeve(13). Mark bracket base mounting hole location on the wall. Drill two holes in the finished wall as required. Press the anchors into the holes and screw the self-tapping screws into the anchors though the sleeve. Tighten them by screwdriver. Aline the bugle of the bracket and the slot of the sleeve. Slide the bracket onto the sleeve and insert the locking pin into the hole of bracket and sleeve.如何安装托架先将固定销(11) 从托架(10) 上扣下,把塑料套 (13)取出。将托架内腔中的自攻螺钉(12) 和胀塞(14) 取出。在淋浴软管可及的高度,选择一个安装托架的位置。在墙壁上标上安装托架底板位置的记号,按记号钻两个洞。将胀塞插入洞中,然后按照图所示将自攻螺钉通过塑料套旋入胀塞中,用螺丝刀拧紧。将托架内壁的凹槽对准塑料套的凸台插入,然后将按钉按入托架的固定孔中。安装 结果检查 INSTALLATION CHECKOUT检查并确保所有的衔接处都已拧紧。确定手柄在“关”的位置。打开排水系统和主要供水源,检查并修理有漏水的接口。将起泡器(15)和花洒(8)拆下,打开水龙头的冷热水,让水流出一分钟以清除杂质。检查渗漏,冲洗起泡器,关闭水龙头,重新装回起泡器和花洒。Ensure that all coupling nuts are tight.Ensure that the handle is in the off position.Turn on the main water supply, and check for leaks. Repair as needed.Remove the aerator(15) and hand spray(8).$Run hot and cold water through the faucet for about one minute to remove any debris. Check for leaks. Remove any debris from the aerator assembly. Shut the faucet off, and reinstall the aerator assembly and handspray.111113清 理说明 CLEANING INSTRUCTIONS适用于所有加工处理过的表面:以中性肥皂水清洗镀层表面,再以干净的软布彻底擦干整个表面,许多清洁剂,比如氨水、去污粉及洁厕灵等,会对电镀表面造成伤害,切忌使用。有磨损性的清洁用具或清洁剂也不可使用于科勒牌的水龙头及其配件上。All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc. which could adversely affect the finish and are not recommended for cleaning.Do not use abrasive cleaners or solvents on Kohler faucets and fittings. 14
展开阅读全文
  微传网所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。
0条评论

还可以输入200字符

暂无评论,赶快抢占沙发吧。

关于本文
本文标题:科勒花洒~72722t_72723t.pdf
链接地址:https://www.weizhuannet.com/p-9852815.html
微传网是一个办公文档、学习资料下载的在线文档分享平台!

网站资源均来自网络,如有侵权,请联系客服删除!

 网站客服QQ:80879498  会员QQ群:727456886

copyright@ 2018-2028 微传网络工作室版权所有

     经营许可证编号:冀ICP备18006529号-1 ,公安局备案号:13028102000124

收起
展开